11 Years Factory wholesale Rubber glove-household sale to Jakarta

FAQ Content

Video tutorial on how to diagnose and repair the blend door actuator on a Ford Ranger. The two main issues with a failing blend door actuator is when you adjust the interior temperature on the hvac control panel, you will either hear a clicking sound or the temperature will be stuck on either hot, cold, or won’t adjust the cabin temperature. If you catch the issue in the right time, then it is repairable and you don’t need to buy a replacement actuator. This particular vehicle I am working with is a 1998 Ford Ranger, but a similar procedure may also apply to Mazda B series models as well.

Website: http://4diyers.com
Patreon: https://www.patreon.com/4diyers
Facebook: https://www.facebook.com/4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: http://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-grease
-cloth
-contact cleaner
-blend door actuator
-gear replacement
-multimeter
-standard/flat screwdriver

Procedure:
-as mentioned above the two main issues is you will either hear a clicking sound in the dash when adjusting the temperature or the temperature can’t be adjusted
-it is located behind the glove box
-remove the contents of the glove box, then bend the sides in and pull down
-this will expose the main duct and the blend door actuator is either a white or black box, this will depend if it’s been replaced before or not and is located on the top
-remove the electrical connector, simply depress the tab and pull out
-the electrical connector can be both back probed using a multimeter when in place or disconnected to test the controller circuit
-wiring may vary between the years so check a wiring diagram specific to your vehicle
-the pinout diagram will say which pin location connects to what part of the circuit
-turn the ignition in the run position
-using a multimeter on the lowest DC voltage setting, check to ensure if there is power at the circuit, along with a sufficient ground
-now setting the multimeter to the lowest ohms setting, we will measure the resistance of the potentiometer in the hvac control panel
-values will vary depending on what your cabin temperature is set at
-if it fails any parts of the test, then there is an issue with the hvac control panel or the wiring
-we can simply remove the actuator and inspect if it’s functioning correctly
-to remove it, simply depress the two tabs on the front and use a standard screwdriver to pop it up
-use the assistance of a standard screwdriver to disconnect the actuator
-another issue is that the shaft can break, either on the unit or on the door within the duct
-if the door has broken within the duct, then the duct will need to be disassembled for replacement
-plug the actuator back into the electrical connector, turn the ignition in the run position and test
-rotate the air temperature control and watch to see if the shaft rotates
-it doesn’t have a large amount of movement and won’t move fast either
-using a smaller standard screwdriver, slowly pop the tabs around the outside
-try to hold it apart so it doesn’t clip closed again
-remove the cap and then everything will be exposed inside
-wipe off any old lubricant
-I used a paint marker just to align the gears to make it easier for reassembly
-then remove the gears and continue to clean off the old lubricant
-inspect gears for any damage
-the small gear driven by the motor, I have seen a replacement on Ebay if yours needs to be replaced and it’s much cheaper than buying a new replacement unit
-clean the potentiometer with electronic contact clean and a clean rag
-do not contaminate this area with any oil or grease and inspect for any damage
-ensure the contacts on the shaft gear which run against the potentiometer is cleaner and make sure they ride correctly on the swipe area
-apply lithium grease to the gears and shafts they ride on
-reassemble the gears, lining everything back up and ensure the case is snapped back together
-test to make sure it is working correctly
-for reinstalling the actuator back onto the duct, if you have moved it, then that’s not an issue
-connect the electrical connector, turn the ignition on and then slowly rotate temperature selector, eventually the actuator will fall into it’s slot, then snap the unit back into place
-test again
-push the glovebox back into place by pulling in the sides again

Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

La Porte Tool Box presents,…..Tool of the Week (week 35)
Glove
From Wikipedia, the free encyclopedia

A glove (Middle English from Old English glof) is a garment covering the whole hand. Gloves have separate sheaths or openings for each finger and the thumb; if there is an opening but no covering sheath for each finger they are called “fingerless gloves”. Fingerless gloves with one large opening rather than individual openings for each finger are sometimes called gauntlets.
Gloves protect and comfort hands against cold or heat, damage by friction, abrasion or chemicals, and disease; or in turn to provide a guard for what a bare hand should not touch. Latex, nitrile rubber or vinyl disposable gloves are often worn by health care professionals as hygiene and contamination protection measures. Police officers often wear them to work in crime scenes to prevent destroying evidence in the scene. Many criminals wear gloves to avoid leaving fingerprints, which makes the crime investigation more difficult. However, the gloves themselves can leave prints that are just as unique as human fingerprints. After collecting glove prints, law enforcement can then match them to gloves that they have collected as evidence. In many jurisdictions the act of wearing gloves itself while committing a crime can be prosecuted as an inchoate offense.

Gloves are made of materials including cloth, knitted or felted wool, leather, rubber, latex, neoprene, and metal (as in mail). Gloves of kevlar protect the wearer from cuts. Gloves and gauntlets are integral components of pressure suits and spacesuits such as the Apollo/Skylab A7L which went to the moon. Spacesuit gloves combine toughness and environmental protection with a degree of sensitivity and flexibility.

History

Minoan youths boxing, Knossos fresco. One of the earliest documented use of gloves.
Gloves appear to be of great antiquity. According to some translations of Homer’s The Odyssey, Laërtes is described as wearing gloves while walking in his garden so as to avoid the brambles. (Other translations, however, insist that Laertes pulled his long sleeves over his hands.) Herodotus, in The History of Herodotus (440 BC), tells how Leotychides was incriminated by a glove (gauntlet) full of silver that he received as a bribe There are also occasional references to the use of gloves among the Romans as well. Pliny the Younger (c. 100), his uncle’s shorthand writer wore gloves in winter so as not to impede the elder Pliny’s work.

A gauntlet, which could be a glove made of leather or some kind of metal armour, was a strategic part of a soldier’s defense throughout the Middle Ages, but the advent of firearms made hand-to-hand combat rare. As a result, the need for gauntlets also disappeared.

Pontifical gloves are liturgical ornaments used primarily by the pope, the cardinals, and bishops. They may be worn only at the celebration of mass. The liturgical use of gloves has not been traced beyond the beginning of the 10th century, and their introduction may have been due to a simple desire to keep the hands clean for the holy mysteries, but others suggest that they were adopted as part of the increasing pomp with which the Carolingian bishops were surrounding themselves. From the Frankish kingdom the custom spread to Rome, where liturgical gloves are first heard of in the earlier half of the 11th century.
When short sleeves came into fashion in the 1700s, women began to wear long gloves, reaching half-way up the forearm. By the 1870s, buttoned kid, silk, or velvet gloves were worn with evening or dinner dress, but long suede gloves were also worn during the day and when having tea.

In 1905 The Law Times made one of the first references to the use of gloves by criminals to hide fingerprints, stating: For the future… when the burglar goes a-burgling, a pair of gloves will form a necessary part of his outfit.

Early Formula One race cars used steering wheels taken directly from road cars. They were normally made from wood, necessitating the use of driving gloves
.
Music
Air Hockey Saloon by Chris Zabriskie is licensed under a Attribution License.
Permissions beyond the scope of this license may be available at http://chriszabriskie.com/licensing or contact artist via email.
http://freemusicarchive.org/music/chris_zabriskie/vendaface/05_-_air_hockey_saloon — at La Porte, La Porte, Texas.