15 Years Manufacturer Rubber shoe cover Denver Factory

FAQ Content

Be cautious when holding key components that have sensitive contact areas. If you want to be extra cautious you can use tech grade ESD gloves. I recommend ESD Nitrile gloves that have microtextured fingertips that provide excellent grip on all surfaces. 100% nitrile gloves contain no natural rubber or silicone and meet stringent requirements for particles and extractables. In regards to handling try not to directly handle PCB or contact points. For a graphics card try to handle it from the corners or the heatsink. For a motherboard use the corners / sides. If you do not want to use full gloves you can also consider finger ESD cods. If you use your bare hands just have common sense and keep in mind when the contacts are.

I mistakenly refer to the measurement on the gloves thickness as millimeters, when in fact it is milli-inches. MIL stands for milli-inches and MM stands for millimeters. My bad. Though, that doesn’t change anything I say as inaccurate regarding smaller number = thinner glove.

ESD Nitrile Gloves:

http://amzn.to/2rbxvVN

If you’re trying to prevent fingerprints, wash your hands thoroughly with soap and water, paying particular attention to scrubbing the pads on your fingers. Dry them off well. Then handle the components by the edges, as I demonstrate in all of my computer building videos. If you happen to see a fingerprint, stop. Go wash your hands again! This is a much better plan than using any kind of glove.

Remember, handle all parts by the edges and there is no place for fingerprints to be left behind! I demonstrate this in every single computer build video I’ve ever done.

If you’re trying to prevent cuts, these gloves are all too thin to provide any protection from that. Work slower and more carefully to avoid injury. Or put on band-aids prematurely in areas of your hands that you feel you are most prone to be cut.

Video editing software used to create this video:
Cyberlink PowerDirector 15 Ultimate:

https://www.cyberlink.com/products/powerdirector-ultra/

Screen captures by Camtasia Studio 9:

https://www.techsmith.com/camtasia.html

Questions?

https://www.facebook.com/careyholzmanfanpage

See more of Carey’s video’s here:

http://www.CareyHolzman.com

A new luggage series for a super sports car, created by the Porsche Design Studio

Stuttgart. The new Porsche 918 Spyder luggage set presented by Porsche Tequipment is the first suitcase and bag series specially designed for trips away in this high-performance Sports Car. Designed by the Porsche Design Studio and developed by Porsche in Weissach, the luggage collection is an ideal match for the interior of the super sports car. The material concept of these luxurious accessories is based on those used in the passenger compartment of the 918 Spyder*, and the set is also designed to make optimum use of the space available in the vehicle. The series is available in three versions: as a five-piece luggage set, a three-piece travel set or a two-piece stowage set. The entire set comprises two storage boxes, two garment covers and a trolley.

The trolley was specially designed to fit the luggage compartment of the 918 Spyder and has a capacity of 30 litres. Its unusual form means that it leaves more than enough space in the luggage compartment to stow the removable roof halves of the 918 Spyder as well. The trolley can be expanded to hold an additional 10 litres if necessary.

A carbon case for the centre console is also included in the collection. The box opens on the passenger’s side and fits into the elevated centre console, providing stowage space of around 4 litres.

An additional small storage box utilises the space in the glove box for secure stowage. The fact that it is opened and closed using the flap of the glove compartment means that it is ideally integrated into the vehicle.
The luggage set is rounded off by two garment covers which can be securely attached to the carbon-fibre monocoque behind the seats thanks to a specially designed hanging system. The magnetic clasps on the inside of the garment protectors make it easier to fold them together. The protective covers are also shaped to fit the available space, unlike conventional garment covers.

The 918 Spyder luggage series is “Handmade in Germany”. The pieces of luggage are made from a unique high-quality combination of exposed carbon and authentic natural leather. The insides of the boxes, the garment covers and the suitcase are lined with Alcantara. The set thus references the popular motor sports materials which are also used in the interior of the 918 Spyder. The luggage set is available in the same versions as the vehicle interior: Garnet Red-Silver, Onyx Black-Acid Green, Onyx Black-Silver, Mocca Brown-Silver and Mocca Brown-Orange.

Wherever you are in the world, the “Tequipment Accessories Finder” at www.porsche.com/tequipment can be used to search online for information about products from Porsche Tequipment. The online portal’s search function provides a quick and easy overview of the Porsche accessories range.

*Porsche 918 Spyder: combined fuel consumption: 3.1 — 3.0 l/100 km; combined energy consumption: 12.7 kWh/100 km; CO2 emissions: 72 — 70 g/km

Source:
Porsche AG
Product and Technology Communication
Read more about it here: http://dedeporsche.com/2014/07/16/travel-in-style-in-the-porsche-918-spyder-luggage-set/