China wholesale for 24″ rubber glove with cotton linning-rough finish Greenland Supplier

FAQ Content

I’m the Evil Ted who makes props and costumes. I’ve worked on Star Trek Into Darkness, Walking Dead, Fifth Element and Guyver, among lots of others. I’ve made pretty much everything out of every material, but foam is my favorite.

I’m here to share my skills and shortcuts, and help you learn how to make foam costumes and props, too.

To see more, check out my site: http://eviltedsmith.com

Song: Winter Gravity by PetRUalitY
Audio Jungle purchase

Here are some links to make your shopping easier.

How to make a duct tape body form

http://bit.ly/1RDdIBl

How to make a Head Cast

http://bit.ly/1OjwQoJ

Head forms

http://bit.ly/1RRL0Pc

Male body dress form

http://amzn.to/1UJte4I

Female body form

http://amzn.to/1PLRo69

Floor mat foam roll

http://amzn.to/1PLSdfc

Floor mats

http://amzn.to/1ZSjR1U

TNT Cosplay foam

http://bit.ly/1TprI6e

Foam rubber tubbing

http://bit.ly/1SH2pu6

Cutting mats

http://amzn.to/1N2louV

Barge Cement

http://amzn.to/1X4TXWS

Dermel 200 tool

http://amzn.to/1MInS6P

Knife -Box-cutter

http://amzn.to/1N2n07J

X-ACTO Knife

http://amzn.to/1pSKlDI

Metal ruler

http://amzn.to/1pSKpDt

Flexible ruler

http://amzn.to/1pSKt67

Blade Sharpener

http://amzn.to/1ZSlBbd

Heat Gun

http://amzn.to/1RuReWu

Wood burner

http://amzn.to/1UJwlJT

Propane Torch

http://amzn.to/1X4W396

Belt Sander

http://amzn.to/1MIpduc

3M 77 spray glue

http://amzn.to/1MIpgWQ

Glue Pot

http://amzn.to/1M8230p

Mog Podge

http://amzn.to/1X4Wq3D

Kwik seal

http://amzn.to/1X4WsZm

Weldwood cement, great for sealing foam.

http://amzn.to/1UJxlhc

Plastic dip spray

http://amzn.to/1N2rqf2

Ballon latex

http://bit.ly/1iFoJmd

Black proline tint

http://bit.ly/1eRx2Hz

Latex tint

http://bit.ly/P8pdH4

Spray gun

http://amzn.to/1X4WGPZ

Spray gun repair kit

http://amzn.to/1pSMNKu

Future Floor wax

http://amzn.to/1pSMUpg

Shopping with these links helps support this channel.
Thank you

To pick up a Set of the Finishing and Polishing Mandrels, click on the below link:

http://etsy.me/1UcRSJ1

* For a complete list of the highest quality coin ring-making tools, visit my Shop page at:

http://www.CoinRingUSA.com

There’s a lot of information on how to fold and reduce coins to make coin rings, but almost no information on HOW to actually go about and professionally finish and polish the thinner, non-reeded cut edge of your coin rings…

Now you can speed up the finishing process of coin ring-making and obtain the best most uniform high quality smooth, shiny, and even finish to the NON-REEDED edges of your coin rings by quickly getting rid of those unsightly, uneven, sharp edges with this Finishing AND Polishing Mandrel Set!.

No more having to use nail buffing files, sanding by hand, using steel round files or deburring tools to finish your rough coin ring edges… nothing else performs better in completing this critical aspect of coin ring-making.

This Professional set of 3 different-sized Finishing and Polishing Mandrels are designed to give your coin rings that professional-looking quality finish on the edge that was originally the inner part of the coin that is so hard to achieve and will finish and polish any coin ring from an approximate US size of 5, up to an approximate US size of 14.

The Kit comes with a precision German-made stainless steel shank complete with 3 interchangeable uniquely-designed abrasion resistant mandrel cones in the following sizes:

Small — (fits ring sizes of approx. 5-8),
Medium — (fits ring sizes of approx. 8.5-11),
Large — (fits ring sizes of approx. 11-14).

To change from one size to another, you simply hold the tapered rubber mandrel with one hand and twist the steel shank with the other…. no tools are necessary!

The advantage to using the finishing and polishing mandrels is that as the ring is held on tightly to the tapered mandrel that’s spinning while being attached to your power drill; it acts much like a small lathe, providing a much more uniform finish to the ring than can be achieved with either hand-sanding, using a nail buffing file, a steel round-file, or even a small rotary tool such as a Dremel.

*** TO BEGIN ***

1.) Determine which size Polishing Tapered Mandrel fits your completed coin ring, and slide the coin ring on to it.

2.) Place the Mandrel bit into your power drill and tighten.

3.) Adjust the coin ring until it’s well-balanced with no “wobbling” on the Mandrel with your power drill on, and then expand the Mandrel by tightening the Stainless Steel Phillips head set screw at the top which holds the coin ring securely in place.

4.) Begin on the outer edge of the coin ring with the coarser 100 Grit sandpaper and work your way around to the inner edge of the coin ring; making sure that ONLY the corner tip of the sandpaper is making contact with the unfinished inner, top, and outer edges of your coin ring to prevent damage to the rings’ detail. Take your time with this step; especially when you’re first starting out.

5.) Continue to work the inner, top, and outer edges of the NON-REEDED side using the finer Grits of sandpaper as you go; finishing with “0000” Steel Wool. You can also use the steel wool and LIGHTLY go over the inner and the outer detail of the coin ring before you either polish it with a jeweler’s cloth or after you’ve put a patina (antique-looking) finish on the ring.

6.) The final step is to use a jeweler’s cloth to both buff and finish-polish your coin ring.

Your ring will now have a highly-smoothed, rounded, and polished edge on the NON-REEDED side that is not often seen on coin rings!

Other materials needed: a power drill, 3 different grits of sandpaper (I use 100 Grit, 500 Grit, and 1,000 Grit), some “0000” Steel Wool, and a jeweler’s polishing cloth to complete this process. Those items can be purchased from Amazon.com; at a big box store like Home Depot, or any local hardware store inexpensively.

*** SAFETY FIRST ***
- Always wear safety glasses and work gloves.
- Always use caution when working with any power tools and electricity.
- Keep fingers, long hair, and loose clothing away from any fast moving parts.

Description: “How to Get Smooth Rounded Edges to the Rough Cut Side of Coin Rings!”