High Definition For 26″ Industrial rubber glove-smooth finish Paris Factory
Short Description:
26″ length (65-67cm), black, smooth finish, seamless, no cotton lining, left/right hand, 700g/pair, cuff perimeter:61cm, double layer thickness:2.2mm. 50 pairs/case, carton size: 74*36*44cm. Net weight: 35kg/case, gross weight: 37kg/case. It can be suitable used for sand blasting cabinet operation.
Product Detail
FAQ
Product Tags
The company keeps to the operation concept "scientific management, high quality and efficiency primacy, customer supreme, High Definition For 26″ Industrial rubber glove-smooth finish Paris Factory, With a wide range, good quality, reasonable prices and good service, we will be your best business partner. We welcome new and old customers from all walks of life to contact us for future business relationships and achieving mutual success!
26″ length (65-67cm), black, smooth finish, seamless, no cotton lining, left/right hand, 700g/pair, cuff perimeter:61cm, double layer thickness:2.2mm. 50 pairs/case, carton size: 74*36*44cm. Net weight: 35kg/case, gross weight: 37kg/case. It can be suitable used for sand blasting cabinet operation.
FAQ Content
In this video, I show how to fix a common problem with the blower door actuator on a 2010 Ford F-150 XLT. Here is the part that I installed into the truck. http://amzn.to/2f0Vgue
2003- 2008 Blend Door Actuator Ford F-150
http://amzn.to/2oVwtNh
2009- 2014 Blend Door Actuator Ford F-150 (THIS IS THE MODEL I USED)
http://amzn.to/2f0Vgue
2015- Present
http://amzn.to/2qvKL4s
Dashboard Plastic Remover Tool:
http://amzn.to/2pVlmUE
Note: Make sure this fits within your model. I know its hard to find the parts sometimes, so I hope you use these links above as a guide to finding your actuator.
This F-150 would only blow cold air because the actuator for the blower door went out. Before I went this far to replace the part I started a few diagnoses: tested the air conditioner, went under the hood to see if the heater core hoses were hot, and check the internet if this was a common issue. Sure enough, every test lead to a faulty actuator.
The hardest part was jamming my hand through the glove box. In order to get to the 5/16in screw on the bottom, I had to go through the glove box while my left hand was in the dash to help assist. Once I got the screw out it was fairly simple.
Installing the new unit took a little bit of wiggling in there because the actuator and door need to be lined up. It can only fit one way. The gear is keyed for this reason. Once installed, connect the power cord, install the two screws that hold the unit down, and put the dash all back together.
This process took about 45 minutes to complete. After the install I was able to change from hot to cold with ease.
Thanks for watching:
Subscribe- http://goo.gl/nD3r4v
Like
Comment
Enjoy
http://goo.gl/7nHNTA Click link for your degreaser, this stuff works well.
Learn how to remove dried paint or overspray from your car. In this video I demonstrate techniques to remove dried paint speckles from my truck Disclaimer:
Doublewide6 has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’s videos. Use this information at your own risk. Doublewide6 recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6. Please support Doublewide6 by donating to his Patreon Account https://www.patreon.com/doublewide6




