High Quality for Rubber foot cover sale to Madras

FAQ Content

Peppa and her friends and family go for a daytrip to the snowy beach. / Peppa and her family get lost in the fog, but meet some friends along the way. / It is raining outside so Peppa and George have to stay indoors. / Peppa and her friends are on Snowy Mountain learning how to ski. / Peppa’s family are staying at Cousin Chloe’s house, but baby Alexander’s crying is keeping everyone awake! / Peppa and her friends go for a sleepover at Zoë Zebra’s house. / Peppa and George have fun looking for a torch and thinking of games to play in the dark. / Peppa and George stay up late to help hunt for slugs, snails and other night animals. / Suzy and Peppa start a Secret Club, but soon everyone wants to join! / George has fun looking at himself in the mirror and tries to find other shiny things. / Pedro get a cough at playschool and the other children quickly catch it. / Mummy Pig gives Peppa a special box to keep secret things in.

Here I am doing basic glass cutting on a scrap piece of glass, actually it’s a mirror. For much more videos about basic glass cutting, etc. see the playlist: http://www.youtube.com/playlist?list=PL4A57AB2EFB9566F9&feature=plcp

Do not attempt to cut (pre) Tempered Glass, it cannot be cut and is designed to shatter to small pieces for safty purposes. You can cut (flat) Plate Glass.

The “glass cutter” does not actually cut through the glass, it just scratches or “scores” it, so it should be called either a “glass scratcher/scorer” or a “tool of glass cutting”.

The score is then used when you actually break or snap the glass along this “weakened” line (or even curves are possible). Technically, you try to “bend” both sides along the score downward to “open” (not compress) the crack up to the back side of the glass. In the vid. I show holding the piece of glass with my hands as a lot of people seem to do – especially with small pieces, but it’s safer to put the glass on a firm surface first and/or wear gloves.

To remove the sharp parts after cutting the glass, I used some sandstone I found down by the river. Just about any stone or cement will do, just dont use something too hard like smooth quartz since it tends to just “glide” over the glass. Use both straight and circular motion with the stone at about a 45 degree angle to the glass to bevel it to a non-sharp/thin semi-round surface. It is good though to have an electric grinder or rotary tool like a Dremel incase the break leaves some sizeable bumps of glass areas that would be difficult to grind by hand. If you dont have that, perhaps a larger piece of smooth cement might work ok.

Be sure to sweep up and vacuum any glass shards.

Note you can use a flat rule made of metal, wood, or plastic to guide the glass cutter, but be sure its not too thin since you do not want to damage the “cutting wheel” (the part that scores the glass) if it came in contact with metal.

About the tool I made; the ruler-straightedge with the rubber attached to the back. The rubber (or nylon) was cut from a bicycle inner-tube, and was attached with contact cement which is very sticky and somewhat flexible. This glue is sometimes called “rubber cement”. I got a tube for about $1. I also lightly scratched both surfaces of the rubber for better adhesion of the glue and for better “holding” ability on the glass. I guess you could also use some flat erasor type material too instead of the inner tube material. Silicone rubber or a thin coat or beads of dried caulking might be ok. Some tape can possibly be used to secure the straightrule, but you might have to clean up any residue left from the tape unless you put the tape right on the rule itself. When you cut the bicycle tube, avoid breathing the powder (usually talc or talcum), so rinse the tube segment with hot soapy water and let it dry.

Keep the “scoring wheel” oiled. I just keep/store that end in a glass with some clear oil in it. I use cheap “mineral oil” from the dollar/drug store.

Find some flat glass pieces and practice a bit on them so that you are prepared to cut glass when you need to.

Here is a good website about glass cutters, care and use:

http://www.freepatternsforstainedglass.com/your-glass-cutter.html