Wholesale Price China 14″ Household rubber glove in Cannes

FAQ Content

Learn How to Clean Skateboard Grip Tape by using natural rubber pieces.
Go to http://ratvision.com/ for more info.

Most videos and websites explain how to clean grip tape using window cleaner and scrubbing with a toothbrush. This can actually do more harm than good.

Grip tape is made of different layers of material. The windex can affect the material and damage the grip tape. Some brands of skateboard grip tape are perforated. This means very tiny holes are all over the grip tape. What this does is help eliminate air bubbles when applying the grip tape to a skateboard.

Perforated grip tape allows window cleaner or water to soak through and possibly ruin the adhesive of the grip tape and damage the wood of the deck.

We recommend cleaning skateboard grip tape with natural rubber pieces. At skate shops this rubber is sold as the brand name Grip Gum. This same rubber can be found at almost any hardware store and is known as “belt sander cleaner”. Grip Gum and belt sander cleaner are sold between $6-8. These pieces will last for a large number of grip tape cleanings. At nearly any art supply store you can find small pieces of rubber for about $2 that is called “rubber cement pick-up” or “crepe rubber”.

Unfortunately, these rubber pieces clean only the dirt and dust on the top surface of the grip tape. In order to get into deep in the grit you need to scrub it off. Many videos demonstrate using a toothbrush. This may work for some jobs, but for most jobs a toothbrush will not get down deep or scrub hard enough. The bristles are not tough and durable enough to do a good job on street or longboard skateboard grip tape.

The best brush to use is a soft brass wire brush. A brass wire brush is able to scrub hard enough to remove crud down deep in the grip tape, and the bristles are not too stiff or hard to damage the sharp edges of the grit.

Steps for cleaning standard (Street or Longboard) grip tape:
1. Scrub dirty spots with wire brush
2. Scrub/wipe off dirt with natural rubber piece.

For really coarse grit in longboard grip tape the wire brush and rubber piece may not get the job done. Since, these grip tapes are very coarse they require a lot of resin to hold the grit, which makes these grip tapes incapable of being perforated. Because these grip tapes are not perforated it is OK to use water if needed.

Steps for Cleaning coarse longboard grip tape:
1. Dip wire brush in water
2. Scrub dirty spots with wire brush
3. Pat the wet or “muddy” area with a towel until dry. Avoid paper if possible, since it tears in the grip tape. Use a hair dryer to dry the grip tape quickly. Avoid high heat. The rubber will slide easily and clean poorly when wet or on a wet surface. This is why it is best to dry the grip tape as much as possible before using the rubber.
4. Scrub the remaining dirt/dust with the rubber piece.

CLEAR or COLORED GRIP TAPE CLEANING:
Clear and colored grip tape use Aluminum Oxide grip. DO NOT use a wire brush for clear or colored grip tape. Colored grip tape actually uses a colored resin that holds the clear (aluminum oxide) grit in place. If you scratch this grip tape with a bush it will make the grit turn white.

INSTRUCTIONS:
1. Try using a natural rubber and see if that cleans the grip tape to your satisfaction.
2. If the grip is still too dirty you can use a lightly damp cloth to clean the grip tape, and then use the rubber to clean it even further.

For any questions about this video or anything skate related send us a message.
For more info on grip tape and what makes one brand better than another check out the article on skateboard grip tape at RatVision.com

The Little Giant Overhaul™ ladder system was designed by firefighters for firefighters. The Overhaul ladder extends to 17 feet but is small enough to carry into an elevator, up a flight of stairs, or around tight corners. The ladder is just 4 foot 7 inches tall when retracted.

The Overhaul has been engineered to combat all the unique challenges that firefighters have to face every day:

Ratchet™ Levelers – Working on unlevel ground due to slope or debris? Ratchet Levelers adjust in seconds to provide an even, level setup over an uneven surface or debris. Ratchet Levelers are specifically designed to be easy to operate while wearing heavy firefighting gloves and boots.
Roof & Rafter Hooks – The Overhaul Ladder is equipped with folding roof and rafter hooks that allow firefighters to hook the ladder to a rafter or truss to help prevent the ladder from “slipping out” from underneath while firefighters work during overhaul and other operations.
High-Visibility – Each rung on the Overhaul Ladder is equipped high-viz reflective labels and Little Giant’s exclusive Safety Insight™ photo-luminescent strips to help identify rung location in low light conditions. This durable material glows for up to 16-hours when charged, is integrated into the rung, and will not rub off like tape.
Dual Position Spike Feet – Adjustable non-slip rubber feet provide stability on wet or slippery surfaces and flip down spike feet provide stability on grass, carpet and soft surfaces.
Easy Transport – The Overhaul Ladder is equipped with heavy duty casters for quick, easy transport.
Easy Carrying – The Overhaul Ladder is designed to be extremely mobile and easy to move from place to place. It is equipped with a large, solid aluminum carrying handle that is easy to grip while wearing firefighter gloves.
Heat Sensing Technology – The Defender has special heat-sensing labels that indicate when the ladder has been exposed to too damaging temperatures and should be taken out of service.
NFPA Compliance

The Little Giant Overhaul ladder system is designed to meet the requirements of NFPA 1931-2015, Standard for Manufacturer’s Design of Fire Department Ground Ladders, and has been tested to the requirements of NFPA 1932-2015, Standard on Use, Maintenance, and Service Testing of In-Service Fire Department Ground Ladders.

Little Giant’s Overhaul and Defender ladders are the only articulating ladder systems that meet the requirements of NFPA 1901-2009, Standard for Automotive Fire Apparatus, section 5.7.1.3 for pumpers, section 8.7.5 for ladder trucks, and section 9.7.1.3 for quints.

Insurance Services Office

The Little Giant Overhaul Ladder meets ISO requirements for credit on pumper and ladder apparatus.