Wholesale price for 32″ Large cuff rubber glove sale to Mozambique

FAQ Content

Learn how to make these awesome jalapeno poppers stuffed with cream and shredded cheese and BACON!! Double breaded and deep fried, these are sure to be a hit for your family or next get together! Perfect appetizer for parties, the Super Bowl, football games or just as a snack for the kids.

What you’ll need:
8 jalapeno peppers
8 oz cream cheese, softened
1/4 cup shredded co-jack cheese
4-5 slices bacon
2 eggs
1/4 cup milk
1/2 cup all-purpose flour
2 cups dry breadcrumbs
oil for frying

Start by frying the bacon. When nice and crispy, drain on paper towels and let cool.
To prep the peppers, cut in half lengthwise and scoop out the seeds and veins using a spoon. Use gloves for this is you have open sores or sensitive skin on your hands. Set aside.
In a medium bowl, combine the cream and shredded cheese. Add in crumbled bacon and stir to mix well. Put about 1 tablespoon of filling in each pepper half. Press down firmly into the pepper so there are no air pockets. Mound the filling up slightly. Continue with the rest of the pepper halves.
In a small bowl add the flour. In another bowl add the breadcrumbs. In a third bowl, combine the eggs and milk. Start the breading process by dipping the poppers into the egg, then the flour. Shake off excess flour and put back into the egg mixture. Let excess drip off and then dredge in the breadcrumbs. Set onto a plate and continue with the rest of the peppers. Let dry for about 10 minutes and then bread again by dipping into the egg again and back into the breadcrumbs. Again, let dry for 10 minutes before frying.
Heat oil in a heavy bottomed pan and heat over medium-high heat until oil reaches 350*F. When the oil is ready, slowly and carefully put a couple poppers into the oil and fry for 2-3 minutes or until golden brown. Remove to a paper towel lined plate to drain of excess oil. Serve with ranch dressing or your favorite dipping sauce. Makes 16 poppers. Enjoy!!

My Links:
Google+: https://plus.google.com/+croutoncrackerjacks
Facebook: https://www.facebook.com/pages/Crouton-Crackerjacks/549691821747028
Pinterest: https://www.pinterest.com/crackerjackj/

Music by Kevin MacLeod: (http://incompetech.com)

Here I am doing basic glass cutting on a scrap piece of glass, actually it’s a mirror. For much more videos about basic glass cutting, etc. see the playlist: http://www.youtube.com/playlist?list=PL4A57AB2EFB9566F9&feature=plcp

Do not attempt to cut (pre) Tempered Glass, it cannot be cut and is designed to shatter to small pieces for safty purposes. You can cut (flat) Plate Glass.

The “glass cutter” does not actually cut through the glass, it just scratches or “scores” it, so it should be called either a “glass scratcher/scorer” or a “tool of glass cutting”.

The score is then used when you actually break or snap the glass along this “weakened” line (or even curves are possible). Technically, you try to “bend” both sides along the score downward to “open” (not compress) the crack up to the back side of the glass. In the vid. I show holding the piece of glass with my hands as a lot of people seem to do – especially with small pieces, but it’s safer to put the glass on a firm surface first and/or wear gloves.

To remove the sharp parts after cutting the glass, I used some sandstone I found down by the river. Just about any stone or cement will do, just dont use something too hard like smooth quartz since it tends to just “glide” over the glass. Use both straight and circular motion with the stone at about a 45 degree angle to the glass to bevel it to a non-sharp/thin semi-round surface. It is good though to have an electric grinder or rotary tool like a Dremel incase the break leaves some sizeable bumps of glass areas that would be difficult to grind by hand. If you dont have that, perhaps a larger piece of smooth cement might work ok.

Be sure to sweep up and vacuum any glass shards.

Note you can use a flat rule made of metal, wood, or plastic to guide the glass cutter, but be sure its not too thin since you do not want to damage the “cutting wheel” (the part that scores the glass) if it came in contact with metal.

About the tool I made; the ruler-straightedge with the rubber attached to the back. The rubber (or nylon) was cut from a bicycle inner-tube, and was attached with contact cement which is very sticky and somewhat flexible. This glue is sometimes called “rubber cement”. I got a tube for about $1. I also lightly scratched both surfaces of the rubber for better adhesion of the glue and for better “holding” ability on the glass. I guess you could also use some flat erasor type material too instead of the inner tube material. Silicone rubber or a thin coat or beads of dried caulking might be ok. Some tape can possibly be used to secure the straightrule, but you might have to clean up any residue left from the tape unless you put the tape right on the rule itself. When you cut the bicycle tube, avoid breathing the powder (usually talc or talcum), so rinse the tube segment with hot soapy water and let it dry.

Keep the “scoring wheel” oiled. I just keep/store that end in a glass with some clear oil in it. I use cheap “mineral oil” from the dollar/drug store.

Find some flat glass pieces and practice a bit on them so that you are prepared to cut glass when you need to.

Here is a good website about glass cutters, care and use:

http://www.freepatternsforstainedglass.com/your-glass-cutter.html