17 Years Factory 32”rubber glove-cotton linning to Muscat Factory

Short Description:

Heavy duty rubber glove,  made of 100% natural latex. 32”length(82cm), smooth finish, seamless, cotton lining, left/right hand, 800g/pair, 50 pairs/case. Using for Isolater, dry box, blast cabinet, etc.


Product Detail

FAQ

Product Tags

Our products are widely recognized and trusted by users and can meet continuously developing economic and social needs. 17 Years Factory 32”rubber glove-cotton linning to Muscat Factory, Create Values,Serving Customer!" is the aim we pursue. We sincerely hope that all customers will establish long term and mutually beneficial cooperation with us.If you wish to get more details about our company, Please contact with us now.


Heavy duty rubber glove,  made of 100% natural latex. 32”length(82cm), smooth finish, seamless, cotton lining, left/right hand, 800g/pair, 50 pairs/case. Using for Isolater, dry box, blast cabinet, etc.

  • Previous:
  • Next:
  • FAQ Content




  • Video slideshow that outlines how to repair sheet metal. This demonstration was done on a lawn tractor mower deck, but the same principles can be applied to auto body work on vehicles. Most automotive body panels do use a thinner gauge steel, so when welding, more care will have to be taken to reduce the amount of heat distortion. In the video I did use a flux core mig welder, but an argon unit can be used as well.

    Website: http://4diyers.com
    Facebook: https://www.facebook.com/4diyers
    Google Plus: https://plus.google.com/+4DIYers
    Twitter: https://twitter.com/4DIYers
    Instagram: https://www.instagram.com/4diyers/
    Tumblr: http://4diyers.tumblr.com
    Pintrest: https://www.pinterest.com/4diyers/

    Tools/Supplies Needed:
    -angle grinder
    -angle grinder cutting disks
    -angle grinder flap wheels
    -locking pliers
    -mig welder
    -welding shield
    -welding gloves
    -hammer
    -paint marker
    -wire brush
    -220 grit sandpaper
    -paint
    -paint brush
    -safety glasses
    -replacement metal
    -propane torch
    -adjustable wrench
    -clean cloth
    -degreaser

    Procedure:
    -determine to what extent the metal is damaged
    -remove the rusty soft/thin areas will allow for a solid area to weld the patch to and also reduces the chance of having the welder burn through the existing steel
    -cut out the damaged area using a grinder equipped with cutting disks
    -start by forming the new metal to replace the damaged area
    -sometimes it is easier to form the replacement metal first before cutting out the damaged area, but the damaged area should still be in reasonable condition to copy the shape or contours
    -to form the replacement pieces I used a couple concrete blocks, along with some wood for forming, along with the assistance of a hammer, adjustable wrench, and propane torch
    -forming metal will vary depending on what you are trying to achieve
    -for my repair I first bent the metal patches, then made relief cuts using the angle grinder with cutting disks so I could form multiple contours
    -once finished forming the patches, ensure they fit and remove excessive material from the original panel if needed (it’s better to have more newer metal in a patch repair)
    -use the flap wheel for the angle grinder to remove any existing rust or paint to prepare for welding
    -fit the patch into place, use locking pliers to hold it into place
    -ground the mig welder onto the piece, select a proper heat range
    -first tack the replacement piece into place, applying a tack weld every one to two inches
    -adjust piece when needed using a hammer, ensuring the edge lines up correctly
    -once the piece is held in, then continue with short welds about one inch in length in various areas
    -do no run one continuous weld as this will cause warpage
    -allow the metal to cool if need
    -once the welding has finished, use the flap wheel on the angle grinder to smoothen out the welds
    -finally to finish up, for my repair I used a wire brush to clean the mower deck removing any loose rust and paint
    -finish up with 220 grit sandpaper to smoothen out the surface
    -I wiped down the mower deck with a clean cloth and degreaser
    -then applied a farm equipment paint using a brush to the whole mower deck

    The cuts in the one rounded patch allows for the piece to be bent into two different directions to match the contour of the mower deck.
    Grind the paint off around the area where the patch will be welded to. This will ensure that welder is able to arc on the existing surface properly.

    The tack welds hold the piece in place and allow me to align the patch to the existing surface. For the welding, I used a small flux core mig welder.

    Running small/short (approx. 1″ length) welding beads reduces the amount of distortion within the sheet metal which is caused by excessive heat. This will have to be adjusted accordingly depending on the gauge/thickness of steel.

    For grinding down the welds I used the angle grinder with standard grinding disc for the higher areas and a flap disc to smoothen the surface.

    For paint, I used low gloss black farm equipment painted which I brushed on.

    Credit:
    Music:
    Zap Beat – Kevin MacLeod (http://incompetech.com/) Licensed under Creative Commons “Attribution 3.0″ http://creativecommons.org/licenses/by/3.0/

    Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

    © 4DIYers 2013
    All Rights Reserved
    No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.



    “”"Ultimate Hiking Gear & Skills Clinic”"

    A backpacking trip consists of two distinct activities: hiking and camping. In this informative clinic, renowned long-distance backpacker Andrew Skurka will discuss the gear, supplies and skills necessary to make hiking fun, not an arduous chore. Skurka was named “”Adventurer of the Year”" by Outside and was described as “”a Superman among trekkers,”" by National Geographic; he is the author of The Ultimate Hiker’s Gear Guide.

    You will learn: (1) How to predict the environmental and route conditions you will encounter on a trip; (2) the best uses and limitations of lightweight equipment; (3) skills that will help keep you safe and comfortable with a minimum of possessions; and, (4) exactly what Skurka takes for a summer backpacking trip in the Sierra Nevada, and why.”

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Star

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Tree