2016 High quality 24″ rubber glove with cotton linning-smooth finish sale to Sao Paulo

FAQ Content

John from http://www.okraw.com/ shares with you why he is not a hundred% vegan or a hundred% uncooked. You will also find out if everyone is truly a hundred% vegan.. This data will be stunning as it is a rationale that quite a few men and women do not think about.

In this episode, John talks with his twenty five year vegan friend, JD Mumma, who is a vegan advocate about if everyone is truly vegan? This episode will get rid of some light on John’s views about getting vegan, performing the least damage, residing with compassion and empathy and saving the planet.

During this video you will find out how to consider independently alternatively of the “herd” mentality. You will also explore the differences between divergent and convergent thinking and which type would finest provide you as a plant based eater to advertise the vegan way of life.

You will also find out some procedures to advocate the vegan concept to other individuals alternatively of the shaming and bashing that is common in quite a few vegan circles.

Following viewing this episode, you will find out that there are quite a few requirements to getting vegan and that we are all just performing the finest way can to save animals, have better overall health, and do the least damage on the planet.

Follow John on Instagram at:

https://instagram.com/growingyourgreens/

Subscribe to OKRAW for far more videos like this:

https://www.youtube.com/subscription_centre?increase_user=okraw

Learn Much more about JD Mumma at:

http://www.ecopeaceful.com/

https://www.facebook.com/jdmumma

https://www.facebook.com/groups/LongTermVegans

https://www.facebook.com/groups/Vegan.Affect.and.Persuasion/

https://www.facebook.com/groups/Vegan.Influencers.and.Debaters/

Video tutorial on how to diagnose and repair the blend door actuator on a Ford Ranger. The two main issues with a failing blend door actuator is when you adjust the interior temperature on the hvac control panel, you will either hear a clicking sound or the temperature will be stuck on either hot, cold, or won’t adjust the cabin temperature. If you catch the issue in the right time, then it is repairable and you don’t need to buy a replacement actuator. This particular vehicle I am working with is a 1998 Ford Ranger, but a similar procedure may also apply to Mazda B series models as well.

Website: http://4diyers.com
Patreon: https://www.patreon.com/4diyers
Facebook: https://www.facebook.com/4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: http://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-grease
-cloth
-contact cleaner
-blend door actuator
-gear replacement
-multimeter
-standard/flat screwdriver

Procedure:
-as mentioned above the two main issues is you will either hear a clicking sound in the dash when adjusting the temperature or the temperature can’t be adjusted
-it is located behind the glove box
-remove the contents of the glove box, then bend the sides in and pull down
-this will expose the main duct and the blend door actuator is either a white or black box, this will depend if it’s been replaced before or not and is located on the top
-remove the electrical connector, simply depress the tab and pull out
-the electrical connector can be both back probed using a multimeter when in place or disconnected to test the controller circuit
-wiring may vary between the years so check a wiring diagram specific to your vehicle
-the pinout diagram will say which pin location connects to what part of the circuit
-turn the ignition in the run position
-using a multimeter on the lowest DC voltage setting, check to ensure if there is power at the circuit, along with a sufficient ground
-now setting the multimeter to the lowest ohms setting, we will measure the resistance of the potentiometer in the hvac control panel
-values will vary depending on what your cabin temperature is set at
-if it fails any parts of the test, then there is an issue with the hvac control panel or the wiring
-we can simply remove the actuator and inspect if it’s functioning correctly
-to remove it, simply depress the two tabs on the front and use a standard screwdriver to pop it up
-use the assistance of a standard screwdriver to disconnect the actuator
-another issue is that the shaft can break, either on the unit or on the door within the duct
-if the door has broken within the duct, then the duct will need to be disassembled for replacement
-plug the actuator back into the electrical connector, turn the ignition in the run position and test
-rotate the air temperature control and watch to see if the shaft rotates
-it doesn’t have a large amount of movement and won’t move fast either
-using a smaller standard screwdriver, slowly pop the tabs around the outside
-try to hold it apart so it doesn’t clip closed again
-remove the cap and then everything will be exposed inside
-wipe off any old lubricant
-I used a paint marker just to align the gears to make it easier for reassembly
-then remove the gears and continue to clean off the old lubricant
-inspect gears for any damage
-the small gear driven by the motor, I have seen a replacement on Ebay if yours needs to be replaced and it’s much cheaper than buying a new replacement unit
-clean the potentiometer with electronic contact clean and a clean rag
-do not contaminate this area with any oil or grease and inspect for any damage
-ensure the contacts on the shaft gear which run against the potentiometer is cleaner and make sure they ride correctly on the swipe area
-apply lithium grease to the gears and shafts they ride on
-reassemble the gears, lining everything back up and ensure the case is snapped back together
-test to make sure it is working correctly
-for reinstalling the actuator back onto the duct, if you have moved it, then that’s not an issue
-connect the electrical connector, turn the ignition on and then slowly rotate temperature selector, eventually the actuator will fall into it’s slot, then snap the unit back into place
-test again
-push the glovebox back into place by pulling in the sides again

Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.