Factory selling 32″ Large cuff rubber glove to Malaysia Importers

FAQ Content

Please find this product at http://absupply.net/
This video is to bring you a closer look at the Zero 51A-180. This is a piece of finger guard and is an 8″ wide strip of rubber which happens to be a 12″ sample piece. This is used on the push side of a door between the hinge jamb and the face of the door and it is intended for someone to not hurt themself. So your typical installation will look like that and there is this face that will be attached down to the face of the door and this side goes back by the jamb. I might have said that backwards, you are going to create a loop like this is what I am trying to say. One part is going to go to the frame and the other part is going to go to the door and as that door opens it keeps the hinge jamb covered to prevent someone or something from going into that area. This model 8″ wide rubber is specifically intended for a door to go to 180 degrees and you are going to see this in a variety of applications and namely schools, industrial applications, childcare facilities, hospitals, and a variety of workplaces. This is a commercial quality and maintaince free product and surface mounts with screws and are included. There is a link below this video, 1 is a printable cut sheet and it gives you the elevation on how the 51A is installed and there is a dash 120 and that is for a 120 degree opening and the width of the rubber would be smaller because the door does open as much but it shows 120 being discontinued so 180 would be your go to material for this application. There is another link to a page called product brochure that shows the system in a bit greater detail with information and description of the item. You can see how the finger guard is intended to either act alone or to act in conjunction with the 951. Typically schools are going to have heavier doors with grade 1 commercial door calibers to be used and can be put up with some abuse. The doors are heavy and well excess of 100 lbs. On that link to the product brochure you will also see a couple of other items in terms of safety and with automatic doors as well. Finally there is a link below this video to the manufacture’s website where you call pull up the entire catalog and review Zeros custom solutions they have to products. This finger guard is a perfect example of unique solutions Zero has brought to the market. They are a leader in flood gate barriers as well as well as common weather stripping such as door sweeps, perimeter gasketing, and thresholds. If you have any questions on the Zero 51A-180 degree finger guard or any other Zero product please feel free to reach out to us. Thank you very much.

Learn How to Clean Skateboard Grip Tape by using natural rubber pieces.
Go to http://ratvision.com/ for more info.

Most videos and websites explain how to clean grip tape using window cleaner and scrubbing with a toothbrush. This can actually do more harm than good.

Grip tape is made of different layers of material. The windex can affect the material and damage the grip tape. Some brands of skateboard grip tape are perforated. This means very tiny holes are all over the grip tape. What this does is help eliminate air bubbles when applying the grip tape to a skateboard.

Perforated grip tape allows window cleaner or water to soak through and possibly ruin the adhesive of the grip tape and damage the wood of the deck.

We recommend cleaning skateboard grip tape with natural rubber pieces. At skate shops this rubber is sold as the brand name Grip Gum. This same rubber can be found at almost any hardware store and is known as “belt sander cleaner”. Grip Gum and belt sander cleaner are sold between $6-8. These pieces will last for a large number of grip tape cleanings. At nearly any art supply store you can find small pieces of rubber for about $2 that is called “rubber cement pick-up” or “crepe rubber”.

Unfortunately, these rubber pieces clean only the dirt and dust on the top surface of the grip tape. In order to get into deep in the grit you need to scrub it off. Many videos demonstrate using a toothbrush. This may work for some jobs, but for most jobs a toothbrush will not get down deep or scrub hard enough. The bristles are not tough and durable enough to do a good job on street or longboard skateboard grip tape.

The best brush to use is a soft brass wire brush. A brass wire brush is able to scrub hard enough to remove crud down deep in the grip tape, and the bristles are not too stiff or hard to damage the sharp edges of the grit.

Steps for cleaning standard (Street or Longboard) grip tape:
1. Scrub dirty spots with wire brush
2. Scrub/wipe off dirt with natural rubber piece.

For really coarse grit in longboard grip tape the wire brush and rubber piece may not get the job done. Since, these grip tapes are very coarse they require a lot of resin to hold the grit, which makes these grip tapes incapable of being perforated. Because these grip tapes are not perforated it is OK to use water if needed.

Steps for Cleaning coarse longboard grip tape:
1. Dip wire brush in water
2. Scrub dirty spots with wire brush
3. Pat the wet or “muddy” area with a towel until dry. Avoid paper if possible, since it tears in the grip tape. Use a hair dryer to dry the grip tape quickly. Avoid high heat. The rubber will slide easily and clean poorly when wet or on a wet surface. This is why it is best to dry the grip tape as much as possible before using the rubber.
4. Scrub the remaining dirt/dust with the rubber piece.

CLEAR or COLORED GRIP TAPE CLEANING:
Clear and colored grip tape use Aluminum Oxide grip. DO NOT use a wire brush for clear or colored grip tape. Colored grip tape actually uses a colored resin that holds the clear (aluminum oxide) grit in place. If you scratch this grip tape with a bush it will make the grit turn white.

INSTRUCTIONS:
1. Try using a natural rubber and see if that cleans the grip tape to your satisfaction.
2. If the grip is still too dirty you can use a lightly damp cloth to clean the grip tape, and then use the rubber to clean it even further.

For any questions about this video or anything skate related send us a message.
For more info on grip tape and what makes one brand better than another check out the article on skateboard grip tape at RatVision.com