Wholesale Price 32”rubber glove-cotton linning for Portland Factories

FAQ Content

I’m the Evil Ted who makes props and costumes. I’ve worked on Star Trek Into Darkness, Walking Dead, Fifth Element and Guyver, among lots of others. I’ve made pretty much everything out of every material, but foam is my favorite.

I’m here to share my skills and shortcuts, and help you learn how to make foam costumes and props, too.

To see more, check out my site: http://eviltedsmith.com

Song: Winter Gravity by PetRUalitY
Audio Jungle purchase

Here are some links to make your shopping easier.

How to make a duct tape body form

http://bit.ly/1RDdIBl

How to make a Head Cast

http://bit.ly/1OjwQoJ

Head forms

http://bit.ly/1RRL0Pc

Male body dress form

http://amzn.to/1UJte4I

Female body form

http://amzn.to/1PLRo69

Floor mat foam roll

http://amzn.to/1PLSdfc

Floor mats

http://amzn.to/1ZSjR1U

TNT Cosplay foam

http://bit.ly/1TprI6e

Foam rubber tubbing

http://bit.ly/1SH2pu6

Cutting mats

http://amzn.to/1N2louV

Barge Cement

http://amzn.to/1X4TXWS

Dermel 200 tool

http://amzn.to/1MInS6P

Knife -Box-cutter

http://amzn.to/1N2n07J

X-ACTO Knife

http://amzn.to/1pSKlDI

Metal ruler

http://amzn.to/1pSKpDt

Flexible ruler

http://amzn.to/1pSKt67

Blade Sharpener

http://amzn.to/1ZSlBbd

Heat Gun

http://amzn.to/1RuReWu

Wood burner

http://amzn.to/1UJwlJT

Propane Torch

http://amzn.to/1X4W396

Belt Sander

http://amzn.to/1MIpduc

3M 77 spray glue

http://amzn.to/1MIpgWQ

Glue Pot

http://amzn.to/1M8230p

Mog Podge

http://amzn.to/1X4Wq3D

Kwik seal

http://amzn.to/1X4WsZm

Weldwood cement, great for sealing foam.

http://amzn.to/1UJxlhc

Plastic dip spray

http://amzn.to/1N2rqf2

Ballon latex

http://bit.ly/1iFoJmd

Black proline tint

http://bit.ly/1eRx2Hz

Latex tint

http://bit.ly/P8pdH4

Spray gun

http://amzn.to/1X4WGPZ

Spray gun repair kit

http://amzn.to/1pSMNKu

Future Floor wax

http://amzn.to/1pSMUpg

Shopping with these links helps support this channel.
Thank you

Living in The Phoenix Metro Area? 5 Key steps to plaster your pool. Visit us: http://arizona.poolsresurfacing.com. Tel. 602-497-0490.

Replastering a swimming pool here in the Grand Canyon state is certainly not a five-minute job. This doesn’t mean that you have to spend money on hiring a professional to do the job. If you are willing to put some time and effort into the project, it is certainly possible to do it yourself. The average swimming pool will require replastering every 7 to 12 years, depending on the method of installation, and how it has been maintained. Don’t want to read this article, then listen to highlights how to plaster an old pool in 5 important steps. https://drive.google.com/file/d/0B_ZToeIOgA2sT0xOckJSanNxTDA/view?usp=sharing

First for the tools and materials needed for the project. You will need the mix for pool plaster, acid wash, paint, soda ash, compressor for air, face mask, cleaning solution, finishing plaster mix, chisel, goggles, sump pump for submerging the pool, mixture for cement or mortar, air hammer, normal hammer, yard brush, sander, putty knife, brush for acid, buckets, hose, rubber gloves, wheel barrow, shovel, paintbrush and sponge. Here are the 5 steps to plaster your old pool.

1. Drain the swimming pool, and use the sump pump to drain all the water remaining at the bottom of the pool. Clean the pool of all dirt and debris. Use the sponge and cleaning solution for this purpose. Make sure you use an environmentally friendly cleaning solution for this purpose.

2. Identify the problematic areas where plaster has peeled off significantly. Pay attention to the edges and corners of the pool. Take away the loose plaster with the chisel and putty knife. Sand the sharp edges where plaster has been taken off. Make sure you sand the areas at least twice to make the areas clean and neat for easy replastering.

3. Spray an acid wash over the surface. Use the acid brush to spread it effectively. It will help give you a new surface that is conducive to applying new plaster. Rinse away the acid wash by using a hose. Now allow the surface enough time to dry. Once it is completely dry, apply a bond coat for replastering with the use of a roller. Let it dry overnight.

4. Prepare the plaster according to the manufacturer’s instructions. Now apply the plaster using a street trowel. Start at the deepest end of the pool. You should make sure that the plaster applied is at least 3/8 inches thick. Make sure the plaster is evenly applied on all areas. Now let the plaster dry completely. Mix the plaster finish, and apply it evenly at a thickness of 1/4 inches. You may use the trowel this time round too. Check for any flaws and correct them before letting the pool dry completely.

5. The final step is to apply the pool paint to cover the entire surface evenly. Using the paint brush in one direction will offer a smooth finish to the job. Do not use the pool until the paint is completely dry.

The aforementioned article highlights how to plaster an old pool in 5 important steps.

https://plus.google.com/114577359797335718075/posts/GWbgTQknjAf

Follow us:

http://arizona.poolsresurfacing.com

http://news.poolsresurfacing.com/feed

http://twitter.com/johnawhitlock

https://www.facebook.com/pages/Pools-Resurfacing/427966440738398#

https://plus.google.com/u/0/b/114577359797335718075/114577359797335718075/videos?_ga=1.232935006.1127244526.1462640408